快乐三张牌下载官方

          <dfn id='hyo5n'><optgroup id='hyo5n'></optgroup></dfn><tfoot id='hyo5n'><bdo id='hyo5n'><div id='hyo5n'></div><i id='hyo5n'><dt id='hyo5n'></dt></i></bdo></tfoot>

          <ul id='hyo5n'></ul>

          • <small id='kb827'></small><noframes id='kb827'>

          • <tfoot id='kb827'></tfoot>

              <legend id='kb827'><style id='kb827'><dir id='kb827'><q id='kb827'></q></dir></style></legend>
              <i id='kb827'><tr id='kb827'><dt id='kb827'><q id='kb827'><span id='kb827'><b id='kb827'><form id='kb827'><ins id='kb827'></ins><ul id='kb827'></ul><sub id='kb827'></sub></form><legend id='kb827'></legend><bdo id='kb827'><pre id='kb827'><center id='kb827'></center></pre></bdo></b><th id='kb827'></th></span></q></dt></tr></i><div id='kb827'><tfoot id='kb827'></tfoot><dl id='kb827'><fieldset id='kb827'></fieldset></dl></div>

                  <bdo id='kb827'></bdo><ul id='kb827'></ul>

                  1. <li id='kb827'><abbr id='kb827'></abbr></li>
                  2. 快乐三张牌下载官方 Company News

                    Do You Know The Process Of Pcb? (Down)

                    Feb. 13, 2020

                    3.Brown

                    快乐三张牌下载官方Purpose: To form a microscopic rough and organic metal layer on the copper surface of the inner layer to enhance the adhesion between the layers.

                    Process principle:

                    Through chemical treatment, a uniform organic metal layer structure with good adhesion properties is produced, and the surface of the copper layer is controlled to be roughened before the inner layer is bonded.

                    4.Lamination

                    Lamination is the process of bonding the layers of circuits into one piece by virtue of the adhesion of the pp sheet. This bonding is achieved through the interdiffusion and infiltration of macromolecules at the interface, and then intertwined. The discrete multi-layer board and the pp sheet are pressed together to form a multi-layer board of the required number and thickness. In actual operation, copper foil, adhesive sheet (pre-hardened sheet), inner layer board, stainless steel, insulation board, kraft paper, outer steel plate and other materials are laminated according to the process requirements.

                    For designers, the first thing to consider when laminating is symmetry. Because the board will be affected by pressure and temperature during lamination, there will still be stress in the board after lamination is completed. Therefore, if the two sides of the laminated board are not uniform, the stress on the two sides will be different, causing the PCB board快乐三张牌下载官方 to bend to one side, which greatly affects the PCB performance.

                    快乐三张牌下载官方In addition, even on the same plane, if the distribution of copper is not uniform, the resin flow speed will be different at each point, so the thickness of the place where the copper is less will be slightly thinner, and the thickness of the place where the copper is more will be slightly thicker. 

                    In order to avoid these problems, the factors such as the uniformity of copper distribution, the symmetry of the stack, the design and layout of the blind and buried holes must be carefully considered during the design.

                    Pcb Board

                    Pcb Board

                    快乐三张牌下载官方5. Drilling

                    快乐三张牌下载官方Through holes are created between the layers of the circuit board to achieve the purpose of connecting the layers.

                    快乐三张牌下载官方6.Sinking copper plate

                    快乐三张牌下载官方1) Shen copper

                    It is also called chemical copper. After drilling, the PCB board undergoes a redox reaction in a sinking copper tank, forming a copper layer to metalize the holes, and depositing copper on the surface of the original insulating substrate to achieve electrical communication between layers.

                    2) Plate plating

                    Make the PCB that has just been settled out of copper to thicken the copper in the hole to 5-8um, to prevent the thin copper in the hole from being oxidized and slightly etched away from the substrate before the pattern plating.

                    快乐三张牌下载官方7. Outer dry film

                    快乐三张牌下载官方The process is the same as the inner dry film.

                    8. Outer layer graphic plating, SES

                    Add holes and circuit copper layers to a certain thickness (20-25um) to meet the requirements of the final copper thickness of the finished PCB board. And useless copper on the board surface is etched away, revealing useful circuit patterns.

                    9. Solder mask

                    快乐三张牌下载官方Solder mask, also known as solder mask, green oil, is one of the most critical processes in the production of printed boards. It is mainly by screen printing or coating solder mask ink, coating a layer of solder mask on the board surface, and developing by exposure. , To expose the disks and holes to be soldered, and cover the other parts with a solder mask to prevent short circuits during soldering

                    快乐三张牌下载官方10. Silk screen characters

                    快乐三张牌下载官方The required text, trademark or part symbol is printed on the surface of the board by screen printing, and then exposed on the surface of the board by ultraviolet irradiation.

                    快乐三张牌下载官方11. Surface treatment

                    快乐三张牌下载官方Bare copper itself has good solderability, but it is susceptible to moisture and oxidation when exposed to air for a long time. It tends to exist in the form of oxides, and it is unlikely to remain as copper for a long time. Therefore, the copper surface needs to be surface treated. The most basic purpose of surface treatment is to ensure good solderability or electrical properties.

                    快乐三张牌下载官方12. Forming

                    The PCB is cut into the required external dimensions by a CNC molding machine.

                    13. Electrical test

                    The state of the simulation board, power on to check the electrical performance, whether there is open or short circuit.

                    14. Final inspection, spot testing, packaging

                    Check the appearance, size, aperture, plate thickness and marking of the board to meet customer requirements. Pack qualified products into bundles for easy storage and shipping.

                    We are a PCB board manufacturer. We provide high quality OSP printed circuit boards快乐三张牌下载官方. If you have any requirements for our products, please feel free to contact us.


                    Previous: How Was Pcb Born?(Up)

                    Next: Do You Know The Process Of Pcb? (On)快乐三张牌下载官方

                    蓝洞棋牌官网送3金币---首页_Welcome 靠谱的棋牌---首页_Welcome 摩比棋牌---HOME_Welcome 上棋牌---首页_欢迎您 有什么好玩棋牌游戏-Welcome